EC997 Dyno Accessories

Replacement for older and slower Andros and on special order, Horiba units - In other words, if your dyne system has an integrated Andros, this unit should usually drop right in.	Factory Pro Hi Speed 4 gas / 5 gas EGA 4 or optional 5 gas EGA: High speed - with quick moisture removal Designed for continuous duty with minimal attention Typical Response: movement: 2 to 3 secs 90% settle: 4 to 6 secs Case, Stainless steel, brushed finish, heavy gauge, custom: looks new after years of service Handles, built in for easy transport These units feature the reliable Andros 6500 bench: USB or serial communication, standard Andros communication protocol Internal solenoid for zeroing air sample Standard Andros "Zero" procedure Electronic Factory Pro "Desecater" for exhaust moisture removal Anodized aluminum desecater for long life and fast heat transfer rate high flow rate, low restriction liquid water constantly evacuated by dedicated micro pump Transport sample gas: Multi-filtered: 40 micron, 40 micron, 15 micron Easy, external filter access Standard type air filters allowing local procurement Transport sample filter location: Mounted on front facing "flip plate" for easy filter inspection and maintenance Sample gas filter: 5 micron - helps keeps EGA bench clean for reliability Power 110vac (or special order 220vac) Replaces Horiba EGA and others. pn: DYNO-EGA-4G-000 High Speed, continuous duty, Exhaust Gas Analyzer, 4 gas price: $8250
	EGA Sample Transport Pump Diaphragm and Reed Valve Rebuild Kit 1. Choose your shipping method 2.
	SCU Speed Calibration Unit The SCU is used to electronically calibrate the EC997 DAQ unit and to check wiring faults. Features active LEDs indicating cabling status. Direct plugin to standard EC997 dyne MIL-SPEC speed sensor cable connection. The SCU should be used every 6 months to check for internal drift to maintain elevated levels of accuracy. The SCU should be used to troubleshoot potential speed sensor, speed sensor cabling and DAQ speed or rpm issues. The SCU must be used when setting up new PAU box power supply min, max, IR limits and damping values.	pn: DYNO-SCU-2048 price: $500
no picture	Calibration Weight, load cell (also called: strain gauge, torque link) NIST traceable load cell calibration weight is used weekly to verify proper electronic load cell calibration. Proper load cell zero and span values are key, along with electronic SCU speed sensor calibration, are critical for accurate dynamometer horsepower readings.	pn: DYNO-CALWT-50 price: $500
	Manual Dyno Controller (optional equipment) To manually control load in EC997 systems. Useful for troubleshooting and diagnostic operation. Requires USB EC997 Controller Unit and may require minor box mods, depending on USB version. Call to check.	pn: DY-Man-CTRLR-000 price: $1000 (requires USB controller box)
	Exhaust Sample Hose Filters, 10 pc mini pack helps prevent fiberglass from clogging EGA devices on any brand of dyno Special 75 micron Prefilters for exhaust gas sample hose - Cheap, throw-away filter. Replace every few tests or when dirty - Helps keep fiberglass and silencing material from clogging main EGA filters. 5/16" / 8mm hose 75 micron (can be used as a fuel filter, too) Bulk packaged	pn: DY-FI-EGA-51675-10 price: $40.00 / 10 pcs ($4.00 ea) 1. Choose your shipping method 2.
	Exhaust Sample Hose Filters, 30 pc maxi pack\| helps prevent fiberglass from clogging EGA devices on any brand of dyno Special 75 micron Prefilters for exhaust gas sample hose - Cheap, throw-away filter. Replace every few tests or when dirty - Helps keep fiberglass and silencing material from clogging main EGA filters. 5/16" / 8mm hose 75 micron (can be used as a fuel filter, too) Bulk packaged	pn: DY-FI-EGA-516-75-30 price: $99.95 / 30 pcs ($3.33 ea) 1. Choose your shipping method 2.